Valcom V2904 Dokumentacja Pobierz pdf (Strona 10)

Entry Delay Time

If a key entry occurs at a door (an entry not using the

dialpad or remote button) the remote button must be

pressed or the confirmation code must be dialed on

the telephone keypad. This must be done within a

designated period of time after the door is opened

signifying a legitimate door opening or an alert will

sound. The default time for the confirmation press is

15 seconds. This time can be changed by:

1. Lift handset and hear dial tone.

2. Press # 1 2 3 # 8.

3. Enter station number (1-4) or * for all stations.

4. Enter time length in seconds (0-999).

5. Press #.

6. Receive dial tone.

Duration of Ringing

When a door button is pressed, it activates the phone

into a ring cycle. The ring cycle will continue for a

programmed time period and stop if unanswered.

The default equals approximately 30 seconds. To

change this default:

1. Lift handset and receive dial tone.

2. Press # 1 2 3 # 5.

3. Enter station number (1-4) or * for all stations.

4. Enter ringing duration (1-255 seconds)

(0 = no time out)

5. Press #.

6. Receive dial tone.

Disable Station Alarm

On power up, the station alarm condition is active. In

the event a doorway or gate would need to be left

open for an extended time (or at least longer than the

programmed time it can remain open before an alarm

condition), the alarm can be disabled.

To leave door open without causing an alarm

condition:

1. Lift handset and receive dial tone.

2. Press 5.

3. Press station number (1-4) to be disabled or *

for all stations.

4. Enter disable code (default is *; this may have

been changed).

5. Receive dial tone.

The default code for disabling the station alarm

condition is *. To change this default:

1. Lift handset and hear dial tone.

2. Press # 1 2 3 *.

3. Enter station number (1-4) or * for all stations.

4. Enter up to 7 digits.

5. Press #.

6. Receive dial tone.

NOTE: When a disabled station is accessed, the

alert tone will be at a lower tone as a reminder

that the alarm at that station has been disabled.

To enable a door alarm that has been disabled:

1. Lift handset and receive dial tone.

2. Press 6.

3. Press station number (1-4) or * for all stations.

4. Receive dial tone.

Alert Tone

The phone and station receives a ringback tone prior

to connection. Default - the station receives the tone.

To remove the alert tone:

1. Lift handset and receive dial tone.

2. Press # 1 2 3 # 9.

3. Enter station number (1-4) or * for all stations.

4. Press 0.

5. Press #.

6. Receive dial tone.

To re-activate the alert tone:

1. Lift handset and receive dial tone.

2. Press # 1 2 3 # 9.

3. Enter station number (1-4) or * for all stations.

4. Press 1.

5. Press #.

6. Receive dial tone.

Door Detect

Some door alarm contacts are closed when the door is

closed and some are open when the door is closed.

By default, the V-2904 uses door alarm contacts that

are open when the door is closed.

To change this default:

1. Lift handset and receive dial tone.

2. Press # 1 2 3 # 0 1.

3. Press # and receive dial tone.

OPERATION

When the doorplate button at a station is pressed,

interrupted ring voltage from the V-2904 initiates

ring-in on the telephone system and sends a

confirmation tone to the door. When the phone is

answered, a series of optional tones may be heard in

the receiver. These tones numerically indicate which

door is calling. These are followed by a ringback

tone and connection to the handsfree speaker. When

the phone is busy with one station and a call is placed

from another station, the person on the telephone will

hear a call waiting tone corresponding to the door

location. (Example: Station 2 - Beep-Beep).

Repeated button presses from the station will cause

repeated signals to the phone provided the presses are

separated by 5 seconds. If the 2nd call is not

answered during the programmed time (determined

by the programmed number of ring cycles) after the

last press, it will lose its power to be answered.

If the door is equipped with an electric strikeplate, a

1 2 ... 5 6 7 8 9 10 11 12 13 14

Komentarze do niniejszej Instrukcji

Brak uwag

Valcom V2904 Dokumentacja Strona 10

Komentarze do niniejszej Instrukcji